KEPCO KLP 10-150-1200 User Manual

Manufacturer
Type
Pages 84 Pages
Updated Sep 3, 2021
Category Power Supply

Table of Contents

  • Power supply

    1
  • Declaration of conformity

    3
  • Safety instructions

    5
  • Scope of Manual

    13
  • KLP Operating Regions

    14
  • KLP Specifications

    15
  • KLP Series Power Supply, Mechanical Outline Drawing

    18
  • Features

    20
  • Overvoltage/Overcurrent Protection

    21
  • Internal Relay

    22
  • Accessories

    23
  • Unpacking and Inspection

    25
  • Analog I/O Switch Functions

    26
  • KLP Series, Rear Panel Switch and Connectors

    27
  • IEEE 488 Port Connector (J4) Pin Assignments

    28
  • LAN Port Connector (J7) Pin Assignments [-1.2K Models Only]

    29
  • Source Power Requirements

    30
  • Installation

    31
  • Safety Grounding

    32
  • D-C Output Grounding

    33
  • Power Supply/Load Interface

    34
  • Series Operation

    35
  • Series Connection using Remote Sensing

    36
  • Load Sharing

    37
  • Analog I/O Connections

    38
  • RS 232 Connections [-1200 Models Only]

    39
  • General

    41
  • Power-up Built-in Test Error Codes

    42
  • Setting Local/Remote Mode

    43
  • Enabling/Disabling Output Power

    44
  • Defining a Virtual Model

    45
  • Setting voltage or current

    46
  • Last Setting Recall

    47
  • Changing GPIB Address

    48
  • Configure power supply as Master [-1200 Models Only]

    49
  • Operating the Master/Slave Configuration [-1200 Models Only]

    50
  • LAN Interface Configuration [-1.2K Models Only]

    51
  • Utility Function

    52
  • Display System Firmware Version

    53
  • Quick Boot

    55
  • Fault Recovery Configuration

    56
  • Analog Input Full Scale Calibration

    57
  • Calibration

    58
  • Additional Functions Not Available from the Front Panel

    59
  • Finding Kepco Power Supplies on the LAN [-1.2K Models Only]

    60
  • Launch Web Interface [-1.2K Models Only]

    61
  • Instrument Configuration Using Web Interface [-1.2K Models Only]

    62
  • LAN Configuration Using Web Interface [-1.2K Models Only]

    63
  • Operating The Unit Using Web Interface [-1.2K Models Only]

    64
  • Changing the Output [-1.2K Models Only]

    65
  • Save/Recall Dialog Box

    66
  • Resetting the Unit (*RST) [-1.2K Models Only]

    67
  • Setting Virtual Model [-1.2K Models Only]

    68
  • Remote Programming Using Analog Signals

    69
  • Programming with external resistance

    70
  • Programming with external Voltage

    71
  • Changing Overvoltage or Overcurrent Protection Values in Analog Programming Mode

    72
  • Equipment Required

    73
  • Calibration Using Front Panel Controls in Local Mode

    74
  • Current Calibration (Local)

    75
  • Calibration Exit (Local)

    76
  • Calibration Window

    77
  • Voltage Calibration (VXI plug&play Driver Demo)

    78
  • Current Calibration (VXI plug&play Demo)

    79
  • Analog Reference Calibration (VXI plug&play Demo)

    80
  • Calibration Exit (VXI plug&play Demo)

    81
  • Restoring Prior Calibration Values

    82

Related Manuals

Below are links to the text of a wide variety of documents related to the KEPCO KLP 10-150-1200 User Manual.