Comtech EF Data UT-4505 Installation And Operation Manual

Manufacturer
Type
Pages 112 Pages
Updated Sep 3, 2021
Category Media Converter

Table of Contents

  • Installation and operation manual

    1
  • CHAPTER 1. INTRODUCTION

    19
  • Figure 1. Front Panel (Model UT-4505 shown)

    20
  • Figure 3. Typical Functional Block Diagram (Model UT-4514 shown)

    21
  • Specifications

    22
  • Table 2. UT-4505/E/F/G/H/J/X Up Converter Specifications

    24
  • Table 3. UT-4505I/M Up Converter Specifications

    26
  • Table 4. UT-4514 and UT-4514/C/D/E/F Up Converter Specifications

    28
  • Table 5. UT-4518 and UT-4518/E Up Converter Specifications

    30
  • Figure 4. UT-4514 Dimensional Envelope

    32
  • Physical Configuration

    33
  • Front Panel Display

    34
  • CHAPTER 2. INSTALLATION

    37
  • Table 6. Rear Panel Connectors

    38
  • Table 7. J1, 2 Wire EIA-485 Interface Pin-Out

    39
  • Table 10. J3, High Speed Bus Connector Pin-Out

    40
  • Cable Connections

    41
  • Figure 7. Non-Redundant Converter Configuration

    42
  • CHAPTER 3. SYSTEM OPERATION

    43
  • Table 12. Operating Functions – Front Panel

    44
  • Operation

    45
  • Figure 12. Converter Operating Command Functions

    46
  • Figure 13. Configuration Menu Commands - Redundancy OFF

    47
  • Figure 14. Configuration Menu Commands - Redundancy ON, Backup Unit Not Selected

    48
  • Figure 15. Configuration Menu Commands - Redundancy ON and Backup Unit Selected

    49
  • Figure 16. Pre-Select Menu Commands

    50
  • Figure 18. Current Faults Menu Commands

    51
  • Figure 20. Utility Function Menu Commands

    52
  • Converter Commands

    53
  • Stored Faults

    56
  • CHAPTER 4. REDUNDANT SYSTEM OPERATION

    59
  • Backup Converter

    60
  • Table 13. 4500 Series Up Converter Configurations

    61
  • Redundant Configurations

    62
  • Figure 25. 1:1 Redundant Configuration - Dual Source IF Input

    64
  • Figure 27. 1:N Redundant Configuration with IOM-XX and TSM-XX Installed

    65
  • Figure 28. 1:N Redundant Configuration Diagram with IOM-XX and TSM-XX Installed

    66
  • Redundant System Configuration

    67
  • Figure 30. 1:3 System in AUTO Redundant Mode

    68
  • Figure 31. Converter #1 Being Backed Up

    69
  • Figure 32. Converter #1 in MANUAL, Others in AUTO

    70
  • Figure 33. Forced BU of Converter #1

    71
  • CHAPTER 5. REMOTE CONTROL

    75
  • Baud Rate

    76
  • Access Methods

    78
  • Start Character

    79
  • Error Response

    80
  • Modes

    87
  • Status Commands

    89
  • Stored Alarm

    93
  • Time-Outs

    95
  • Table 14. Remote Command Summary

    96
  • CHAPTER 6. THEORY OF OPERATION

    99
  • Figure 34. Typical Converter Functional Block Diagram (Model UT-4514 shown)

    101
  • Monitor & Control

    102
  • CHAPTER 7. MAINTENANCE AND TROUBLESHOOTING

    103
  • Figure 35. Converter Signal and Interconnecting Cable Diagram

    104
  • Troubleshooting

    105
  • Converter I/O Modules

    107
  • Test Point Samples

    109

Related Manuals

Below are links to the text of a wide variety of documents related to the Comtech EF Data UT-4505 Installation And Operation Manual.