KEPCO KLP 10-150-(2) User Manual

Manufacturer
Type
Pages 94 Pages
Updated Sep 3, 2021
Category Power Supply

Table of Contents

  • Power supply

    1
  • Declaration of conformity

    3
  • Safety instructions

    5
  • Scope of Manual

    13
  • Options

    14
  • KLP Operating Regions

    15
  • KLP Specifications

    16
  • Physical characteristics

    18
  • KLP Series Power Supply, Mechanical Outline Drawing

    20
  • Features

    22
  • Overvoltage/Overcurrent Protection

    23
  • Internal Relay

    24
  • Accessories

    25
  • Unpacking and Inspection

    27
  • Rear Panel Connectors and Switches

    28
  • KLP Series, Rear Panel Switch and Connectors

    29
  • IEEE 488 Port Connector (J4) Pin Assignments

    30
  • LAN Port Connector (J7) Pin Assignments [E-Series Models Only]

    31
  • Source Power Requirements

    32
  • Installation

    33
  • Safety Grounding

    34
  • D-C Output Grounding

    35
  • Power Supply/Load Interface

    36
  • Series Operation

    37
  • Series Connection using Remote Sensing

    38
  • Load Sharing

    39
  • Master/Slave Configurations [Standard Models Only]

    40
  • Digital Connections

    41
  • General

    43
  • Power-up Built-in Test Error Codes

    44
  • Setting Local/Remote Mode

    45
  • Remote with Local (Front Panel) Lockout

    46
  • Enabling/Disabling Output Power

    47
  • Enabling/Disabling the Output using Remote Inhibit

    48
  • Checking Voltage/Current Setpoints

    49
  • Setting voltage or current

    50
  • Real-time Voltage/Current Adjustment

    51
  • Viewing/Changing Overvoltage or Overcurrent Protection Values

    52
  • Changing RS 232 Baud Rate [Standard Models Only]

    53
  • Configure power supply as Master [Standard Models Only]

    54
  • Operating the Master/Slave Configuration [Standard Models Only]

    55
  • Restoring the Master/Slave Configuration to Standalone operation [Standard Models Only]

    56
  • Unit Configuration

    58
  • Internal Relay Control

    59
  • Quick Boot

    60
  • System Configuration Functions

    61
  • Fault Recovery Configuration

    62
  • Analog Output Full Scale Calibration

    63
  • Analog Input Full Scale Calibration

    64
  • RS 232 Factory Defaults [Standard Models Only]

    65
  • Additional Functions Not Available from the Front Panel

    66
  • Troubleshooting LAN Communication Problems

    67
  • Launch Web Interface [E-Series Models Only]

    68
  • Instrument Configuration Using Web Interface [E-Series Models Only]

    69
  • LAN Configuration Using Web Interface [E-Series Models Only]

    70
  • Web Interface Configure LAN Page

    71
  • Operating The Unit Using Web Interface [E-Series Models Only]

    72
  • Web Interface Operate Instrument Page

    73
  • Resetting the Unit (*RST) [E-Series Models Only]

    74
  • List Dialog Box

    75
  • Setting Virtual Model [E-Series Models Only]

    76
  • Remote Programming Using Analog Signals

    77
  • Programming with external resistance

    78
  • Programming with external Voltage

    79
  • Changing Overvoltage or Overcurrent Protection Values in Analog Programming Mode

    80
  • Equipment Required

    81
  • Calibration Using Front Panel Controls in Local Mode

    82
  • Voltage Calibration (Local)

    83
  • External Calibration (Local)

    84
  • Calibration using VXI plug&play Driver

    85
  • Voltage Calibration (VXI plug&play Driver Demo)

    86
  • Current Calibration (VXI plug&play Demo)

    87
  • Current Calibration Window

    88
  • Analog Reference Calibration (VXI plug&play Demo)

    89
  • Calibration Exit (VXI plug&play Demo)

    90
  • Restoring Prior Calibration Values

    91

Related Manuals

Below are links to the text of a wide variety of documents related to the KEPCO KLP 10-150-(2) User Manual.