Advertisement

Table of Contents
  • Important notices

    3
  • Equipment lists

    11
  • OPERATIONAL OVERVIEW

    13
  • How to Turn the Power On/Off

    14
  • How to Adjust the Brilliance

    15
  • How to Select a Display

    16
  • Highway display

    17
  • Rudder display

    18
  • Numerical display

    19
  • How to select the display data

    20
  • How to select the display data with the key operation (STBY mode only)

    22
  • STEERING MODES

    23
  • How to get the AUTO mode

    24
  • Advanced AUTO mode

    25
  • NAV Mode

    26
  • How to get the NAV mode

    27
  • Sailing method for the NAV mode

    28
  • Waypoint switching method

    29
  • How to set the steering behavior of your boat after you arrive to a waypoint

    30
  • Response Feature

    31
  • TURN Mode

    32
  • Types of normal turns

    33
  • User turn

    34
  • TM turn and start the turn

    35
  • Turns

    38
  • TM turn parameters

    42
  • How to Navigate to a TLL Position

    43
  • DODGE Mode

    44
  • REMOTE Mode

    45
  • Lever-type remote controller (FAP-6221, FAP-6222)

    46
  • Dodge-type remote controller (FAP-6231, FAP-6232)

    47
  • WIND Mode (for sailboats)

    48
  • Wind angle mode

    49
  • TACK mode

    50
  • Tacking in WIND mode (WIND TACK)

    52
  • OVRD mode (for IPS drive)

    56
  • Safe Helm Mode

    57
  • Power Assist Mode

    59
  • ALARMS

    61
  • Alarm Buzzer

    62
  • Watch Alarm

    63
  • XTE Alarm

    64
  • Speed Alarm

    65
  • Water Temperature Alarm

    66
  • Trip Distance Alarm, Trip Distance Reset

    67
  • Wind Alarms (for sailboats)

    68
  • Wind deviation alarm

    69
  • Alarm Log

    70
  • USER MENU

    71
  • Trim gain

    74
  • Speed calculation

    75
  • Net towing

    76
  • Course After Operation of a Remote Controller

    77
  • Nav Data Source

    78
  • NavNet vx2 Synchronization

    79
  • Menu Shortcuts

    81
  • MAINTENANCE, TROUBLESHOOTING

    83
  • Replacement of Fuse

    84
  • Processor unit test

    85
  • Control unit test

    86
  • NMEA0183 test

    87
  • Key test

    88
  • Rudder test

    89
  • Helm sensor test

    93
  • System Data

    94
  • Message board

    95
  • Sensor in Use Display

    98
  • INSTALLATION AND WIRING

    99
  • When FAP-7011 is replaced with FAP-7011C

    100
  • How to install the control unit

    101
  • Wiring

    103
  • Wiring notices

    104
  • Connection with the processor unit

    105
  • INITIAL SETTINGS

    107
  • Display Setup

    109
  • Ship's Characteristics Menu

    110
  • Dockside Setup Menu

    111
  • Rudder limit setup

    113
  • Auto rudder limit

    115
  • Drive unit setup

    117
  • How to set the safe helm mode and power assist mode

    121
  • Confirmation of the dockside setup

    125
  • CAN bus Port Setup

    129
  • NMEA0183 Port Setup

    131
  • Sensor Setup

    133
  • Universal Port Setup

    134
  • GENERAL OUT port setup

    135
  • Sea Trial

    136
  • How to calibrate the compass (PG-500/PG-700)

    137
  • How to set the rudder deadband

    139
  • Data Calibration

    140
  • Parameter Setup Menu

    141
  • NAV Option Menu

    146
  • How to select the source for nav data

    147
  • Fish Hunter Option Menu

    148
  • Wind Option Menu

    149
  • System Setup Menu

    150
  • RC (Remote Controller) Setup Menu

    151